tag:blogger.com,1999:blog-30815160.post6674627213132960600..comments2022-06-07T19:36:15.277-04:00Comments on void (): Error 512 - rear chassis fan not detected on a Small Form FactorSorinhttp://www.blogger.com/profile/18093222184379554605noreply@blogger.comBlogger8125tag:blogger.com,1999:blog-30815160.post-30140249469132683562022-03-11T03:45:01.750-05:002022-03-11T03:45:01.750-05:00Worked well, thanksWorked well, thanksAnonymoushttps://www.blogger.com/profile/04657770780323305975noreply@blogger.comtag:blogger.com,1999:blog-30815160.post-90320464044563918632022-02-27T19:03:17.349-05:002022-02-27T19:03:17.349-05:00Worked perfectly, thank you! The hardest part (for...Worked perfectly, thank you! The hardest part (for me) was getting the pin locked back in place. Had to make sure it was turned the right way.Mark_2.0https://www.blogger.com/profile/00936744556204649645noreply@blogger.comtag:blogger.com,1999:blog-30815160.post-76602156449489338492021-11-23T02:55:13.513-05:002021-11-23T02:55:13.513-05:00Thanks a lot! I was seriously looking for a spot w...Thanks a lot! I was seriously looking for a spot where the syst fan should go. It worked great on my HP Compaq 6200 Pro SFF.Anonymoushttps://www.blogger.com/profile/09066316400899304185noreply@blogger.comtag:blogger.com,1999:blog-30815160.post-41776873176620803852021-05-20T00:50:14.486-04:002021-05-20T00:50:14.486-04:00Works with a SFF ProDesk 600 G1. Used jumper exte...Works with a SFF ProDesk 600 G1. Used jumper extension wires and a small HDD jumper to connect the ground wires of Pin 8 and Pin 9. This is the only post I've seen (of about 30, including videos) that posed this successful solution ...Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-30815160.post-60072200567828752022021-05-08T21:06:23.642-04:002021-05-08T21:06:23.642-04:00Worked for me thanksWorked for me thanksBarnsleyerhttps://www.blogger.com/profile/10653583885306889706noreply@blogger.comtag:blogger.com,1999:blog-30815160.post-77032308072926775012021-04-29T15:47:22.741-04:002021-04-29T15:47:22.741-04:00Great live hack, error 512 no longer appears. Very...Great live hack, error 512 no longer appears. Very good advice.Anonymoushttps://www.blogger.com/profile/00112814144100823214noreply@blogger.comtag:blogger.com,1999:blog-30815160.post-83669293317162052772021-01-13T19:22:45.684-05:002021-01-13T19:22:45.684-05:00works it 6300 SSF
works it 6300 SSF<br />S3b4shttps://www.blogger.com/profile/07933277093006330511noreply@blogger.comtag:blogger.com,1999:blog-30815160.post-65383208742025381102019-08-07T20:57:25.383-04:002019-08-07T20:57:25.383-04:00 Two thumbs up!!
You absolutely nailed it!
Tha... Two thumbs up!! <br /><br />You absolutely nailed it! <br /><br />That fan error if thing has been bugging me for a year! <br /><br />Following the steps above, all you have to do is pull the one black wire on the end of the connector out and then inserted into the empty receptacle directly below. To get the wire out of the harness, use something like a sewing needle or a small eyeglass t42https://www.blogger.com/profile/00803504141643355682noreply@blogger.com